Yaesu FT-1000MP MkV repair

I have added a new page to my WEB about the repair of a seriously ill Yaesu FT-1000MP MKV


You can check it at:

http://jvgavila.com/ft1000mpv.htm

73 JOSE EB5AGV

Yaesu FRG-8800 repair

Lately I spend most of my hobby time fixing rigs for other people. But this time I have fixed a rig for my collection. It is a Yaesu FRG-8800 receiver which suppossedly came with the VHF converter...

When I got it, I found a surprise. It is a heavily modified unit (called Broadcast Monitor Receiver 2) and there is NO VHF converter, but an extra module with balanced audio and IF output on its place, along some other PCBs and other internal mods. You can check what I am talking about here:

This is the company:

http://www.surreyelectronics.com/

This is the mod leaflet front page:

http://www.surreyelectronics.com/leaflets/Receiver2F.jpg

And this is the rear page:

http://www.surreyelectronics.com/leaflets/Receiver2R.jpg

Here you have some pictures:





Well, I knew it was in unworking condition and, really, it didn't work on arrival. No surprise here. I took the covers out to find some oxide in metal cans but mostly a clean receiver. This is the top side:


I polished the cans, dusted it out and started troubleshooting.

AM sort of worked but SSB was completely deaf. While turning the unit to check lower side, I heard some noise inside... and it was a lose piece of PCB!!!. I found it was a PCB corner and it had a trace on it... could this be the cause of the SSB deafness?. I fixed it by glueing and bridging it:




So I put back the PCB, hoping for the best... and no, it was WORSE!!!. Now AM was received faintly and SSB needed about 0.2V to be heard. So I went back to head scratching until I found that pulling the PCB a bit generated some better reception. So I decided to completely remove it:


I took some detailed pictures of the added PCBs:





As you can see, there are a couple IF filters in one PCB, a couple relays in another one and, I guess, a new detector on the third. The mods seem somewhat complex; I guess they are worth more than I have paid for the unit :-)

Looking closely I located the problem. There was another crack in a PCB corner.


I fixed it as follows, scrapping and adding some wire and solder on each crack:



Putting the PCB back got me a pretty hot working receiver :-)!!!. Here you have a very small video (sorry about the lousy quality):



So I decided it was time to clean the unit, removing knobs to clean them sepparately. I also replaced the four display light bulbs, as there was one bad, one dim and two with too much brightness. I put four new lamps.

Here you have some pictures of the cleaned unit, ready for alignment:





Alignment was mostly OK, just some Hertzs out in some oscillators. I used my GPS reference to be sure alignment was done OK.

And this is the result: a perfectly working receiver:



Success!!!

Yaesu FL-2100Z restoration (I)

Well, here I am again :-)

This time I am working on a Yaesu FL-2100Z linear amplifier. I am currently working on it so this post, I hope, will be more interactive than my first one.

I got the unit in a pretty sad condition (yes, it seems all units I get lately are that way!). Price was right, though, so I ended buying it.

Here you have some pictures of the unit so you can see the condition.


Trust me, it looks better in the pictures than in the real world... cabinet has several dents as it has in the front panel top (not seen in these upside down pictures)

Well, let's see the inner top side in detail:




Besides the dirt, it can be seen tubes are Cetron and, probably, original ones. I got a set of chinese National tubes... they were dirty so they had been inside the unit for some time. Why were they removed?... I found it easily, as the top cap snapped in one of the tubes (it seemed burnt!) just when carefully cleaning it and in the other tube, it was loose...


I tried to resolder it but it seems they use some special soldering alloy... I guess it has perhaps some silver. Does anybody know what they use?

Well, let's see the lower side of the unit. I found several things which needed some care. First, there is a relay which is used to modify tube polarization when it is or not transmitting and it was flooded with oil. Not a good thing!


As I had some spares for my FT-102, I decided to replace it:


Once the relay was replaced, I checked one of the problems I knew in advance the unit had: it didn't read SWR... do you guess why?. Check pictures...


I got all the faulty items, from completely dark resistors to dead 1SS97 diodes. I also cleaned the PCB and finally got this:


So I need to replace all the parts and, specially, 1SS97 diodes. I have thought on using 1N5711 Schottky diodes. Any opinion regarding this?

See you on Part II !

73 JOSE EB5AGV